Quantcast Hat problems

news

discussion boards mailing list tips / tricks / forms designs suppliers find a shop marketplace
News
  archives

Discussion
  main menu

Suppliers
  apparel
 
hats
 
thread
  backing
  hoops / hooping
  stock designs

Tips & Tricks
  main menu

Mailing List
  sign up now
 
my account

Amaya Shops
  locate a shop

Marketplace
  shop for supplies

Resources
  official Melco site
  online resources

 

Help Support This Site:


 


 

Results 1 to 3 of 3

Thread: Hat problems

  1. #1
    Join Date
    Apr 2008
    Location
    Kelso, Washington
    Posts
    2
    Post Thanks / Like

    Post

    I have a lot of problems with hats....but only some of the time. ???? I get the usual thread breaks and a lot of false bobbin break alerts so any help with them would be appreciated but my biggest problem right now would be concentric circles or designs with outlines. It looks good on the screen but when it sews there always seems to be one area, somewhere in the design, that the object or outline cover the other. I've got the hat as tight as I can get it, and the acti-feed is set to standard & 8 thickness, 80-12 sharp needle, presser foot three click up from flat sewing, sew speed of 700-1000.... What else do I need to do? Another layer of backing? Faster? Slower? Pull compensation? Any help would be appreciated as I'm just taking shots in the dark right now.
    Thanks, Curtus
    Curtus M.

  2. #2
    Join Date
    May 2006
    Location
    Star, ID
    Posts
    1,551
    Post Thanks / Like

    Post

    Curtus,

    How old is your machine? Is it an XT? What software version are you running?

    Why are you using standard acti-feed and not auto-actifeed? If you are using "standard acti-feed", disable the bobbin detection found under the "Settings" tab. If you have 7.00.xxxx software, are you using the "min auto lower limit" tool found under Settings,Thread feed? ( You must be in the auto acti-feed mode for this to be operational )

    Are you doing your own digitizing? Are these stock designs? Have they been digitized just for cap sewing? i.e. to sew from bottom up and center out? Are you adjusting for minimum column widths?

    Why are you running the presser foot at 3 clicks up? ( the rule of thumb is to have it all the way down and up two, but down more if needed).

    What stlye(s) of cap are we talking about and which one gives you the most problems. How much and what kind of backing are you using on what styles of caps?

    Why an 80/12....75/11 will sew lettering on caps much better. I have yet to need an 80/12 or bigger to sew any caps.

    As you can see, lot more questions than answers, but maybe will give you some ideas to try........

    Rod Springer
    Amaya Tech & Trainer
    Certified tech & trainer<br />208-898-4117

  3. #3
    Join Date
    Feb 2008
    Location
    Bulverde, TX
    Posts
    62
    Post Thanks / Like

    Post

    Curtus,

    I am by far no expert and I'm very new to the business. But I did just complete my first order of 144 hats. Mine were the 6 panel, low profile, brushed twill, unconstructed caps. After many mistakes, this is what worked for me (I have an XT):

    Used 2 layers of tearaway (the slimmer roll made for hats). Make sure both layers of stabilizer goes past the bottom bars on the hoop.

    Used 75/11 sharp needles.

    Used Auto-actifeed.

    Put presser foot all the way down then 2 clicks up.

    Did not run machine any faster than 850.

    I'm not saying this will work for you, but once I ran my machine this way, I hardly had any thread breaks and never had an alignment problem.

    But definitely make sure the design was digitized for caps. The design should stitch from center out and bottom to top.

    Good luck!
    Di<br />Designs by Di

Similar Threads

  1. lettering problems
    By cbireley in forum Machines & Hardware
    Replies: 4
    Last Post: 06-17-2010, 04:41 PM
  2. timing problems, i think. please help
    By Lazydaisy in forum Machines & Hardware
    Replies: 28
    Last Post: 06-10-2010, 01:40 PM
  3. stitching problems
    By Sassyletter in forum Machines & Hardware
    Replies: 2
    Last Post: 04-28-2010, 06:29 PM
  4. 2 Problems!
    By GailForce Designs in forum Machines & Hardware
    Replies: 2
    Last Post: 07-21-2008, 05:33 AM
  5. Report your problems
    By Steve I in forum Embroidery / How Do I?
    Replies: 1
    Last Post: 10-08-2007, 05:12 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
  a Levelbest Network Site - 2013

This site is not owned by or affiliated with Melco or any companies or subsidiaries.